105D | 275/330 Type

$150.00

Out of stock

SKU: KIL-105D Categories: ,

Description

From the early 1920s until the mid 1960s the Rudge-Whitworth design wire wheels were the standard for almost all race cars. Ferrari chose them for the street and race cars and used them as standard equipment or an option through the Daytona series in the early 1970s. The Rudge-Whitworth design wheels were made in Milan as Carlo Borrani wheels until 1961 and as Ruote Borrani after that. They were made with splined hubs and were attached with a central locking nut with two ears and later three ears. These wheel nuts or knock-offs were designed to be removed using a lead hammer. Several different designs were used throughout the years. 275/330 Type.

 

(Sold Individually)

 

 

Product Search: KIL-105D

Related products

  • 107B | Plated spark plug boot tongs

    $600.00     Add to cart

    107B | Plated spark plug boot tongs

     $600.00

    The inside plug twelve cylinder cars had a set of tongs that was used to pull off the spark plug boots when changing the plugs. The plugs were located “inside” the V of the engine between the intake manifolds and were very hard to reach by hand, particularly on a hot racing engine. The early tongs were black. After about 1957 the later tongs were cad-plated. Plated Spark Plug Boot Tongs

     

    (Sold Individually)

     

     

    Product Search: KIL-107B

    Add to cart

  • 100-5 | Button – Type grease fittings (10 x 1 mm)

    $12.00     Add to cart

    100-5 | Button – Type grease fittings (10 x 1 mm)

     $12.00

    Ferrari used these button-type grease fittings from the very earliest cars until the 275’s. During the production of the 250 series cars some of the pieces purchased from outside suppliers used the normal snap-on type. The sealed tie rod ends are a good example showing that a lot of the later cars used both types of grease fittings. The button type grease fittings were made of brass and plated with a very thin layer of nickel. The nickel finish quickly wore off due to dust and dirt on the road plus the factory recommended 2,500 mile lubrication schedule. The button type grease fittings all used the same dimension for the shaft and head but there was a variety of thread sizes. 10x1mm: Used on some of the clutch and brake pedal linkage.

     

    (Sold Individually)

     

     

    Product Search: KIL-100-5

    Add to cart

  • 100-6 | Button – Type grease fittings (11 x 0.75 mm)

    $15.00     Add to cart

    100-6 | Button – Type grease fittings (11 x 0.75 mm)

     $15.00

    Ferrari used these button-type grease fittings from the very earliest cars until the 275’s. During the production of the 250 series cars some of the pieces purchased from outside suppliers used the normal snap-on type. The sealed tie rod ends are a good example showing that a lot of the later cars used both types of grease fittings. The button type grease fittings were made of brass and plated with a very thin layer of nickel. The nickel finish quickly wore off due to dust and dirt on the road plus the factory recommended 2,500 mile lubrication schedule. The button type grease fittings all used the same dimension for the shaft and head but there was a variety of thread sizes. 11 x 0.75mm: Used on the clutch and brake pedal linkage it is not unusual to see both on the same car.

     

    (Sold Individually)

     

     

    Product Search: KIL-100-6

    Add to cart

  • 111B | Cad-plated grease gun hose for the later cars(after about chassis #1,500)

    $200.00     Add to cart

    111B | Cad-plated grease gun hose for the later cars(after about chassis #1,500)

     $200.00

    The tool kits also contained a short flexible hose to be attached to the grease guns for rountine lubrication of the chassis. The early ones had a bronze woven exterior. The later ones had the brass hose plated with Cadmium. Cad – Plated Grease Gun Hose for the later cars (After about chassis #1,500)

     

    (Sold Individually)

     

     

    Product Search: KIL-111B

    Add to cart